【产品简介】：卫生级三通外螺纹球阀在卫生级管道起切换或换向作用，阀体内外采用电离子抛光确保介质无残留在阀体内以达到高卫生标准，该卫生级三通外螺纹球阀可配制电动或气动执行器，以达自动化启闭作用。
卫生级三通外螺纹球阀【主要结构性能参数】：
1☆传动：手轮、气动/电动（带手动）
1 do drive: handwheel, pneumatic/electric （manual）
2☆连接：内螺纹、外螺纹、法兰、焊接、对夹式、卡箍、卡套
Connection: being is 2 internal thread, external thread, flange, welding, clamp, the clamp, the card sets
3☆结构：浮动球、固定球、直通、（T/L型三通）、四通、半球直通等。
3 structure being: floating ball, fixed, straight, （T/L tee, four-way, hemisphere straight, etc.
4☆密封：卫生级橡胶。
4 a seal being: rubber health level.
5☆压力：0.6Mpa≤1.6Mpa
5 fostered pressure: 0.6Mpa≤1.6Mpa
6☆口径：DN20≤DN100
6 diameter being: DN20≤DN100
7☆温度：0℃≤120℃
7 do temperature: 0℃≤120℃
8☆阀体材料：06Cr19Ni10（SUS304） 06Cr17Ni12Mo2（SUS316L）。
8 do the valve body material: 06Cr19Ni10（SUS304） 06Cr17Ni12Mo2（SUS316L）。
9☆介质：洁净水、食用油、牛奶、果汁等。
9 do medium: clean water, cooking oil, milk, fruit juice, etc.
卫生级三通外螺纹球阀【产品特点】：
L型流道的三通4面阀座球阀，采用2面阀座，受力平衡，保证闭止通道上可靠密封。主要用于流路的换向。
T型流道的三通4面阀座球阀，采用4面阀座，受力平衡，保证闭止通道上可靠密封。主要用于分流、混流、换向以及三通道的*开放。
【 features 】 :
L 4 plane seat ball valve port of the tee, USES 2 plane seat, loading balance, guarantee the latch channels and reliable seal. Mainly used for flow reversal.
4 side seat ball valve, the tee T port by seat 4 surface, force equilibrium, guarantee the latch channels and reliable seal. Mainly used for the shunt, mixed flow, reversing and three-channel compley open.
卫生级三通外螺纹球阀【产品使用说明】：
1◆球阀前后管线已准备好。前后管道应同轴，两法兰密封面应平行。管道应能承受球阀的重量，否则管道上必须配有适当的支撑。
2◆把阀前后管线吹扫干净，清除掉管道内的油污、焊渣和一切其它杂质。
3◆核对球阀的标志，查明球阀完好无损。将阀全开全闭数次证实其工作正常。
4◆拆去球阀两端连接上的保护件。
5◆检查阀孔清除可能有的污物，然后清洗阀孔。阀座与球之间即使仅有微小颗粒的异物也可能会损伤阀座密封面。
6◆把阀装上管线。阀的任何一端都可装在上游端。用手柄驱动的阀可安装在管道上的任意位置。但带有齿轮箱或气动驱动器的球阀应直立安装，即安装在水平管道上，且驱动装置处于管道上方。
7◆阀法兰与管线法兰间按管路设计要求装上密封垫。
8◆法兰上的螺栓需对称、逐次、均匀拧紧。
9◆连接气动管线（采用气动驱动器时）。
10◆操作驱动器启、闭球阀数次，应灵活无滞涩，证实其工作正常。
11◆按管路设计要求对管道与球阀间的法兰结合面进行密封性能检查。
【 product use 】 :
1 pieces ball valve before and after the line has been ready. Before and after the pipe shall be concentric, two flange sealing surface should be parallel. Pipe should be able to bear the weight of the ball valve, otherwise the line must be equipped with appropriate support.
2 pieces before and after the valve pipe purging clean, remove all oil pipe, welding slag, and other impurities.
3 pieces to check ball valve, check valve is in good condition. Will be fully open valve full close several times to confirm they work.
4 pieces on the other side of down ball valve connection protection.
5 pieces to check the valve hole clearance may have dirt, and then clean the valve hole. Even if only small particles of foreign bodies between the seat and the ball may also damage the seat sealing surface.
6 pieces put valve on the pipeline. Any end of the valve can be installed at the upstream end. Handle drives the valve can be installed on the pipeline at any position. But with a gear box or pneumatic actuator ball valve shall be installed upright, is installed in a horizontal pipe, and drive in the pipe above.
7 pieces between the valve flange and pipe flange gaskets fitted according to the requirements of pipeline design.
8 mixer flange bolts need to be symmetrical, successive, evenly tighten.
9 pieces connect pneumatic pipe when using the pneumatic drive （）.
10 pieces actuator ball valve opening and closing operation several times, should be no sluggish acerbity, confirmed that they work.
11 pieces according to the requirements of pipeline design and ball valve between the flange joint surface of the pipes to seal performance tests.
【产品】：
上海杰一卫生级阀门专业制造『卫生级三通外螺纹球阀』产品系列：质量可靠，性能稳定。杰一卫生级阀门产品是你放心的选择，我们的目标：质量*、服务*。一年质量保证（包修、包换、包退）除选型错误或人为损坏外
详情请登录杰一阀门* 上海杰一☎：①③⑨①⑥⑦0⑧⑦⑥③
