进口水用过滤器（德国奥莱斯OLES阀门）

进口水用过滤器(德国奥莱斯OLES阀门)

【进口水用过滤器】详细说明：

本过滤器有壳体、排污盖、滤芯、滤网等组成。网眼总面积是入口管首截面积的3-4倍。用于管道清除输送介质:热水、冷水、蒸汽、压缩空气各种机械杂质,特别是锅炉房循环水泵前均需安此产品,为了清除系统中的机械杂质,使设备和管道免受堵塞和磨损,在额定流速下压损为0.05-0.1米水柱。用于各种用汽设备,如:蒸汽仪表、疏水阀,压缩空气和各类用汽设备前均需安装。在额定流速下压损为0.05-0.2米水柱。油过滤器该主品滤眼密度有多种。例如:64孔、200孔、300孔/Cm2。用于各种输油管道上一切设备。例如:油泵、油锅炉前均需安装,在额定流速下压损为0.05-0.1米水柱

The filter consists of a shell, a drainage cover, a filter element, a filter screen, etc. The total area of mesh is 3-4 times of the cross-sectional area of the inlet pipe head. For pipeline cleaning conveying media: hot water, cold water, steam, compressed air all kinds of mechanical impurities, especially before circulating water pump in boiler room, this product should be installed. In order to remove mechanical impurities in the system, so that equipment and pipelines are free from clogging and wear, pressure loss is 0.05-0.1 m water column at rated flow rate. For all kinds of steam equipment, such as steam meters, traps, compressed air and all kinds of steam equipment need to be installed before. Pressure loss is 0.05-0.2 m water column at rated flow rate. Oil filter The main product has a variety of filter density. For example: 64 holes, 200 holes, 300 holes/Cm2. It is used for all kinds of equipment in oil pipelines. For example, oil pumps and oil boilers need to be installed before the pressure loss is 0.05-0.1 m water column at rated flow rate

【进口水用过滤器】工作原理;

该产品安装于进水管路中各配套阀门的前端，当管道中的介质首*入过滤器时，介质通过滤网进入被连接的阀门中，而杂质则留于过滤桶内，使各类阀门不会由于机械杂物卡入密封圈而失灵。

【进口水用过滤器】特点：

1.进出口通径：原则上过滤器的进出口通径不应小于相配套的泵的进口通径一般与进口管路口径*。

2.公称压力：按照过滤管路可能出现的zui高压力确定过滤器的压力等级。

3.孔目数的选择：主要考虑需拦截的杂质粒径依据介质流程工艺要求而定。通水网为18-30目、通气网为40-100目、通油网为100-480目。

4.过滤器材质：过滤器的材质一般选择与所连接的工艺管道材质相同对于不同的服役条件可考虑选择铸铁、碳钢、低合金钢或不锈钢材质的过滤器。

5.过滤器阻力损失计算：在一般计算额定流速下压力损失为0.52～1.2kpa。

产品应用范围：

1.进出口通径：原则上过滤器的进出口通径不应小于相配套的泵的进口通径一般与进口管路口径*。

2.公称压力：按照过滤管路可能出现的zui高压力确定过滤器的压力等级。

3.孔目数的选择：主要考虑需拦截的杂质粒径依据介质流程工艺要求而定。通水网为18-30目、通气网为40-100目、通油网为100-480目。

4.过滤器材质：过滤器的材质一般选择与所连接的工艺管道材质相同对于不同的服役条件可考虑选择铸铁、碳钢、低合金钢或不锈钢材质的过滤器。

5.过滤器阻力损失计算：在一般计算额定流速下压力损失为0.52～1.2kpa。